BETA

106 Amendments of Miriam DALLI related to 2016/0014(COD)

Amendment 42 #
Proposal for a regulation
Recital 7 a (new)
(7a) This Regulation should ensure that the national type-approval authorities interpret, apply and enforce the requirements of this Regulation across the Union. The Commission should be empowered to oversee the work of the national authorities by means of regular audits, re-tests of a random sample of the type-approvals issued and general monitoring of the harmonised application of this Regulation.
2016/09/15
Committee: ENVI
Amendment 46 #
Proposal for a regulation
Recital 9
(9) An effective implementation of the type-approval requirements should be ensured by enhancing the provisions on conformity of production by, inter alia, providing for mandatory periodic audits of the conformity control methods and the continued conformity of the products concerned and by reinforcing and harmonising the requirements relating to the competence, obligations and performance of the technical services that carry out tests for whole-vehicle type- approval under the responsibility of type- approval authorities . The proper functioning of technical services is crucial for ensuring a high level of safety and environmental protection and citizens' confidence in the system. The criteria for designation of technical services provided by Directive 2007/46/EC should be laid down in greater detail in order to assure their consistent application across all Member States. The assessment methods of technical services in the Member States have a tendency to progressively differ due to the increased complexity of their work. Therefore, it is necessary to provide for procedural obligations that ensure an information exchange and monitoring of Member States' practices for the assessment, designation, notification and monitoring of their technical services. Those procedural obligations should remove any existing discrepancies in the methods used and in the interpretation of the criteria for the designation of technical services. In order to ensure adequate oversight and level playing field across Europe, the assessment of the applicant technical service should include the on- site assessment and witnessing the actual type-approval tests.
2016/09/15
Committee: ENVI
Amendment 59 #
Proposal for a regulation
Recital 16
(16) In order to ensure that tests and reports provided by technical services are not influenced by non-legitimate circumstances, the organisation and operation of technical services should ensure full impartiality. To this extent the in-house technical services of the manufacturer should not carry out type- approval and conformity testing for safety, fuel consumption, emissions and other compliance aspects of vehicles and those should be verified by independent third party laboratories only. To be able to carry out their tasks in a coherent and systematic manner the technical services should possess a satisfactory management system including provisions on professional secrecy. In order to allow technical services to perform their work properly, the level of knowledge and competence and independence of their personnel should be guaranteed at all times.
2016/09/15
Committee: ENVI
Amendment 61 #
Proposal for a regulation
Recital 18
(18) A robust compliance enforcement mechanism is necessary in order to ensure that the requirements under this Regulation are met. Ensuring compliance with the type-approval and conformity of production requirements of the legislation governing the automotive sector should remain the key responsibility of the approval authorities, as it is an obligation closely linked to the issuing of the type- approval and requires detailed knowledge of its content. It is therefore important that the performance of approval authorities is regularly verified by means of peer- reviewsubject to regular supervisory controls at Union level, including independent audits, to ensure that a uniform level of quality and stringency is applied by all approval authorities in enforcing the type- approval requirements. Moreover, it is important to provide for the verification of the correctness of the type approval itself.
2016/09/15
Committee: ENVI
Amendment 68 #
Proposal for a regulation
Recital 21 a (new)
(21a) In order to ensure independent testing for in-service compliance throughout the complete life-cycle of all applicable vehicles, robust and mandatory emission testing methods should be developed in order to provide roadworthiness test requirements that are based on the combination of direct tailpipe testing and of OBD testing, including the establishment of test methods for the measurement of NOx during the periodic emission testing pursuant to Directive 2014/45/EU and particulate levels and of their limit values. In particular, new remote sensing technologies can be used to identify grossly polluting vehicles on the road and focus in-service compliance testing for the regulated emission limits (PN, NOx, CO and HC) on these vehicles as the most cost-effective way to carry out periodic technical inspections in the future.
2016/09/15
Committee: ENVI
Amendment 69 #
Proposal for a regulation
Recital 22
(22) In order to increase transparency in the approval process and facilitate the exchange of information and the independent verification by market surveillance authorities, approval authorities and, the Commission, type approval document and third parties, disclosure of vehicle and testing information is necessary to carry out such checks. Relevant information should be provided in electronic format and be made publicly available, subject to exemptions due to protection of commercial interests, intellectual property rights and the protection of personal data, unless it is in the public interest.
2016/09/15
Committee: ENVI
Amendment 72 #
Proposal for a regulation
Recital 24
(24) Those more specific obligations for national authorities provided in this Regulation should include ex-post compliance verification testing and inspections of a sufficient number of vehicles placed on the market. The selection of the vehicles to be subject to this ex-post compliance verification should be based on an appropriate risk assessment which takes account of the seriousness of the possible non-compliance and the likelihood of its occurrence. Moreover, it should be based on clear and detailed criteria and include among others random percentage checks on all current models, on vehicles with a new engine or technology installed, on vehicles with high or very low fuel economy, on vehicles with a very high sales volume and take into account past history of compliance, tips from consumers, results of remote sensing testing as well as concerns of independent research bodies.
2016/09/15
Committee: ENVI
Amendment 78 #
Proposal for a regulation
Recital 27
(27) The objectives of this Regulation should not be affected by the fact that certain systems, components, separate technical units or parts and equipment can be fitted to or in a vehicle after that vehicle has been placed on the market, registered or entered into service. Appropriate measures should therefore be taken to ensure that the systems, components, separate technical units or parts and equipment that can be fitted to or in vehicles and that can significantly impair the functioning of systems that are essential for environmental protection or functional safety are controlled by an approval authority before they are placed on the market, registered or entered into service.
2016/09/15
Committee: ENVI
Amendment 79 #
Proposal for a regulation
Recital 29
(29) Conformity of production is one of the cornerstones of the EU type-approval system, and therefore the arrangements set up by the manufacturer to ensure such conformity should be approved by the competent authority or by an appropriately qualified technical service designated for that purpose but other than the technical service that performed the testing for type- approval purpose, and be subject to regular verification by means of independent periodic audits. In addition, approval authorities should ensure the verification of the continued conformity of the products concerned.
2016/09/15
Committee: ENVI
Amendment 88 #
Proposal for a regulation
Recital 40
(40) Member States should lay down rules on penalties for the infringements of this Regulation and ensure that those rules are implemented. Those penalties should be effective, proportionate and dissuasive. Member States shallould report the imposed penalties to the Commission annually, to monitor the coherence of the implementation of these provisions.
2016/09/15
Committee: ENVI
Amendment 93 #
Proposal for a regulation
Article 3 – paragraph 1 – point 8 a (new)
(8a) 'defeat device' means any element of design which senses temperature, vehicle speed, engine speed (RPM), transmission gear, manifold vacuum or any other parameter for the purpose of activating, modulating, delaying or deactivating the operation of any part of the emission control system, that reduces the effectiveness of the emission control system under all ambient or engine operating conditions regularly pertaining in the territory of the Union and encountered either during normal vehicle operation or outside the type-approval test procedures;
2016/09/15
Committee: ENVI
Amendment 94 #
Proposal for a regulation
Article 3 – paragraph 1 – point 8 b (new)
(8b) 'Base Emission Strategy' (hereinafter 'BES') means an emission strategy that is active throughout the speed and load operating range of the engine unless an AES is activated;
2016/09/15
Committee: ENVI
Amendment 95 #
Proposal for a regulation
Article 3 – paragraph 1 – point 8 c (new)
(8c) 'Auxiliary Emission Strategy' (hereinafter 'AES') means an emission strategy that becomes active and replaces or modifies a base emission strategy for a specific purpose and in response to a specific set of ambient and/or operating conditions and only remains operational as long as those conditions exist;
2016/09/15
Committee: ENVI
Amendment 99 #
Proposal for a regulation
Article 3 – paragraph 1 – point 44 a (new)
(44a) 'remote sensing' means scanning and measuring pollutant levels in a vehicle's exhaust while the vehicle is in motion using sensor-equipped instruments positioned roadside with the purpose of collecting performance data required to monitor the average on-road fleet emissions and identify excessive polluters;
2016/09/15
Committee: ENVI
Amendment 106 #
Proposal for a regulation
Article 6 – paragraph 5
5. Member States shall take the necessary measures to ensure that market surveillance authorities may, where they consider it necessary and justified, be entitled to enter the premises of economic operators without prior notice and seize the necessary samples of vehicles, systems, components and separate technical units for the purposes of compliance testing.
2016/09/15
Committee: ENVI
Amendment 106 #
Proposal for a regulation
Article 3 – paragraph 1 – point 8 a (new)
(8a) 'defeat device' means any element of design which senses temperature, vehicle speed, engine speed (RPM), transmission gear, manifold vacuum or any other parameter for the purpose of activating, modulating, delaying or deactivating the operation of any part of the emission control system, that reduces the effectiveness of the emission control system under all ambient or engine operating conditions regularly pertaining in the territory of the Union and encountered either during normal vehicle operation or outside the type-approval test procedures;
2016/09/20
Committee: TRAN
Amendment 107 #
Proposal for a regulation
Article 3 – paragraph 1 – point 8 b (new)
(8b) 'Base Emission Strategy' (hereinafter 'BES') means an emission strategy that is active throughout the speed and load operating range of the engine unless an AES is activated;
2016/09/20
Committee: TRAN
Amendment 108 #
Proposal for a regulation
Article 3 – paragraph 1 – point 8 c (new)
(8c) 'Auxiliary Emission Strategy' (hereinafter 'AES') means an emission strategy that becomes active and replaces or modifies a base emission strategy for a specific purpose and in response to a specific set of ambient and/or operating conditions and only remains operational as long as those conditions exist;
2016/09/20
Committee: TRAN
Amendment 109 #
Proposal for a regulation
Article 6 – paragraph 6
6. The Member States shall periodically review and assess the functioning of their type-approval activities and the quality of the type-approvals issued. Such reviews and assessments shall be carried out at least every fourtwo years and the results thereof shall be communicated to the other Member States and, the Commission and third parties upon request. The Member State concerned shall make a summaryfull report of the results accessible to the general public, in particular the number of type-approval granted and rejected and the identity of the corresponding manufacturers and vehicle types.
2016/09/15
Committee: ENVI
Amendment 113 #
Proposal for a regulation
Article 6 – paragraph 7
7. The Member States shall periodically review and assess the functioning of their surveillance activities. Such reviews and assessments shall be carried out at least every fourtwo years and the results thereof shall be communicated to the other Member States and, the Commission and third parties upon request. The Member State concerned shall make a summaryfull report of the results accessible to the publicgeneral public free of charge, in particular the number of those vehicles, systems, components or separate technical units that are not in compliance with this Regulation together with the identity of the corresponding manufacturers.
2016/09/15
Committee: ENVI
Amendment 116 #
Proposal for a regulation
Article 7 – paragraph 1 – subparagraph 1 a (new)
Approval authorities shall ensure that the vehicle provided by the manufacturer for the purpose of type-approval testing is fully representative of the vehicle to be produced and placed on the market and which testing does not lead to test results that are systematically divergent from the performance of those vehicles operated under conditions that may reasonably be expected to be encountered in normal operation and use.
2016/09/15
Committee: ENVI
Amendment 117 #
Proposal for a regulation
Article 7 – paragraph 1 a (new)
1a. Approval authorities shall interpret and enforce the requirements of this Regulation in a uniform and consistent manner to avoid divergent standards being applied across the Union. They shall cooperate with the Commission and the Forum in its monitoring and oversight activities as regards the application of this Regulation and provide all the necessary information upon request.
2016/09/15
Committee: ENVI
Amendment 118 #
Proposal for a regulation
Article 7 – paragraph 2
2. Approval authorities shall carry out their duties independently and impartially. They shall observe confidentiality where necessary in order to protect commercial secrets, unless it is in the public interest, subject to the obligation of information laid down in Article 9(3) in order to protect the interests of users in the Union.
2016/09/15
Committee: ENVI
Amendment 120 #
Proposal for a regulation
Article 7 – paragraph 5
5. The Commission mayshall adopt implementing acts to lay down the common criteria to appoint, review and assess the approval authorities at national level. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 87(2).
2016/09/15
Committee: ENVI
Amendment 122 #
Proposal for a regulation
Article 8 – paragraph 1
1. Market surveillance authorities shall perform regular checks to verify compliance of vehicles, systems, components and separate technical units with the requirements set out in this Regulation as well as with the correctness of the type approvals. Those checks shall be performed on an adequate scale, by means of documentary checks and real- drive and laboratory tests on the basis of statistically relevant samples that are representative of the number of vehicles in that member state. When doing so, market surveillance authorities shall take account of established principles of risk assessment, complaints and other information. including complaints, popularity of vehicle models and their parts, third-party testing results, very high or very low fuel economy models, first application of new engine or technology, reports from periodic technical inspections, sampling programmes using remote sensing and other information. In case of vehicles, market surveillance authorities shall aim to cover annually at least 20% of the new models put on the market of the Member State concerned each year to verify that the vehicles comply with the Union safety and environmental legislation.
2016/09/15
Committee: ENVI
Amendment 128 #
Proposal for a regulation
Article 8 – paragraph 1 – subparagraph 1 a (new)
When technical services are designated for the purposes of fulfilling the requirements of this Article, market surveillance authorities shall ensure that a different technical service is used from the one performing tests for the purpose of the original type-approval.
2016/09/15
Committee: ENVI
Amendment 131 #
Proposal for a regulation
Article 8 – paragraph 2
2. Market surveillance authorities shall require economic operators to make the documentation and information available as they consider necessary for the purpose of carrying out their activities. This shall include access to software, algorithms, engine control units and any other technical specifications necessary.
2016/09/15
Committee: ENVI
Amendment 135 #
Proposal for a regulation
Article 8 – paragraph 3 a (new)
3a. For verifying emissions of vehicles, market surveillance authorities may make use of remote sensing technology to help identify highly polluting vehicle models for further investigation. In doing so, the authorities shall cooperate and coordinate their activities with authorities responsible for periodic technical inspections pursuant to Directive 2014/45/EU on periodic roadworthiness tests for motor vehicles.
2016/09/15
Committee: ENVI
Amendment 136 #
Proposal for a regulation
Article 8 – paragraph 4 – subparagraph 1
Market surveillance authorities shall take appropriate measures to alert users within their territories within an adequate timeframe of hazards they have identified relating to any vehicle, system, component and separate technical unit so as to prevent or reduce the risk of injury or other damage. This information shall be made available online in plain and understandable language.
2016/09/15
Committee: ENVI
Amendment 139 #
Proposal for a regulation
Article 8 – paragraph 4 a (new)
4a. The cost of the market surveillance activities pursuant to this article shall be borne by the manufacturers of the vehicles, systems, components and separate technical units concerned.
2016/09/15
Committee: ENVI
Amendment 141 #
Proposal for a regulation
Article 8 – paragraph 5
5. Where the market surveillance authorities of one Member State decide to withdraw a vehicle, system, component and separate technical unit from the market in accordance with Article 49(5), they shall inform the economic operator concerned and where applicable the relevant approval authority.
2016/09/15
Committee: ENVI
Amendment 143 #
Proposal for a regulation
Article 8 – paragraph 6
6. Market surveillance authorities shall carry out their duties independently and impartially. They shall observe confidentiality where necessary in order to protect commercial secrets, unless it is in the public interest, subject to the obligation of information laid down in Article 9(3) to the fullest extent necessary in order to protect the interests of users in the European Union.
2016/09/15
Committee: ENVI
Amendment 146 #
Proposal for a regulation
Article 8 – paragraph 7
7. The Member States shall periodically review and assess the functioning of their surveillance activities. Such reviews and assessments shall be carried out at least every fourtwo years and the results thereof shall be communicated to the other Member States and, the Commission, the Forum and third parties upon request. The Member State concerned shall make a summary of the results accessible to the publicgeneral public in particular the number of those vehicles, systems, components or separate technical units that are not in conformity with this regulation together with the identity of the corresponding manufacturers.
2016/09/15
Committee: ENVI
Amendment 150 #
Proposal for a regulation
Article 8 – paragraph 8 – subparagraph 1 a (new)
The market surveillance authorities shall make publicly available, at least every two years, a summary report of the scope, scale and results of their market surveillance activities.
2016/09/15
Committee: ENVI
Amendment 153 #
Proposal for a regulation
Article 8 – paragraph 10
10. The Commission mayshall adopt implementdelegated acts ing actscordance with Article 88, to lay down the criteria for setting out the scale, scope and frequency with which the compliance verification checks of samples taken referred to in paragraph 1 have to be performed. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 87(2) and criteria for the selection of the vehicles for testing.
2016/09/15
Committee: ENVI
Amendment 160 #
Proposal for a regulation
Article 9 – paragraph 1 – subparagraph 2
Those tests and inspections may take placeshall be carried out on - new vehicles supplied by manufacturers or the economic operator as provided in paragraph 2 below. and - registered vehicles in agreement with the vehicle registration holder.
2016/09/15
Committee: ENVI
Amendment 162 #
Proposal for a regulation
Article 9 – paragraph 1 – subparagraph 3
Those tests and inspections may also take place on registered vehicles in agreement with the vehicle registration holder.deleted
2016/09/15
Committee: ENVI
Amendment 164 #
Proposal for a regulation
Article 9 – paragraph 2
2. Manufacturers holding type- approvals or the economic operators shall, upon request, supply to the Commission a statistically relevant number of production vehicles, systems, components and separate technical units selected by the Commission that are fully representative for the vehicles, systems, components and separate technical units available for placing on the market under that type- approval and be as close as possible to the vehicle used in real world conditions. Those vehicles, systems, components and separate technical units shall be supplied for testing at the time and place and for the period the Commission may require.
2016/09/15
Committee: ENVI
Amendment 172 #
Proposal for a regulation
Article 9 – paragraph 4
4. Vehicle manufacturers shall make public data which are needed for the purpose of compliance verification testing by third parties, including 'road load test data'. The Commission shall adopt implementing acts in order to define the data to be made public and the conditions for such publication, subject to the protection of commercial secrets and the preservation of personal data pursuant to Union and national legislation. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 87(2).
2016/09/15
Committee: ENVI
Amendment 175 #
Proposal for a regulation
Article 9 – paragraph 5 – subparagraph 1 a (new)
Any remedy action taken by the Commission pursuant to its verification testing shall apply Union-wide and shall be implemented by the national authorities in a harmonised and consistent manner. Such Union corrective action may include uniform compensation to consumers if the original vehicles' performance was altered following the remedy action taken as well as financial compensation for any external negative impacts (air quality, public health, etc.).
2016/09/15
Committee: ENVI
Amendment 182 #
Proposal for a regulation
Article 10 – title
Forum foron Enforcement and Exchange of Information on Enforcement
2016/09/15
Committee: ENVI
Amendment 184 #
Proposal for a regulation
Article 10 – paragraph 1 – subparagraph 1
The Commission shall establish and chair a Forum foron Enforcement and Exchange of Information on Enforcement (‘the Forum’).
2016/09/15
Committee: ENVI
Amendment 186 #
Proposal for a regulation
Article 10 – paragraph 1 – subparagraph 2
This Forum shall be composed of members appointed by the Member States, representatives of the Commission and the European Parliament. As observers, it shall include representatives of technical services, third-party testing organisations, safety and environment NGOs and consumer groups.
2016/09/15
Committee: ENVI
Amendment 192 #
Proposal for a regulation
Article 10 – paragraph 2 – subparagraph 1 a (new)
The Forum shall carry out joint audits of the national type-approval authorities every 3 years to verify they comply with the requirements of this Regulation and carry out their duties in an independent and rigorous manner. The audits shall include a verification of the national type approval procedures put in place, a random sample check of the type approvals issued and an on-site visit to a technical service under the responsibility of the reviewed authority. The Commission may participate in the audit and decide on its participation on the basis of a risk assessment analysis. If the audit demonstrates that the authority concerned has breached any of the requirements of this Regulation, it shall immediately take all steps necessary to bring its procedures back in compliance in line with the recommendations issued by the audit. The Forum shall have powers to levy sanctions on the authority concerned. Other Member States shall not recognise the type approvals issued to vehicles, systems, components and separate technical units by the authority concerned on their territory until full compliance with the requirements of this Regulation and the audit recommendations is put in place. The Forum shall coordinate market surveillance activities in line with Article 8 to avoid duplication and ensure cost- effectiveness. It shall in particular advise on the samples to be checked according to the principles of risk assessment and ensure the required number of vehicles, systems, components and separate technical units is surveyed by the market surveillance authorities annually across the Union.
2016/09/15
Committee: ENVI
Amendment 194 #
Proposal for a regulation
Article 10 – paragraph 2 – subparagraph 2
Its advisory tasks shall also comprise inter alia the promotion of good practices, the exchange of information on enforcement problems, cooperation, development of working methods and tools, development of an electronic information exchange procedure, evaluation of harmonised enforcement projects, penalties and joint inspections.
2016/09/15
Committee: ENVI
Amendment 195 #
Proposal for a regulation
Article 10 – paragraph 2 – subparagraph 2 a (new)
All decisions taken and recommendations agreed upon by the Forum shall be made public including on recalls.
2016/09/15
Committee: ENVI
Amendment 197 #
Proposal for a regulation
Article 10 – paragraph 3
3. The Commission shall be empowered to adopt delegated acts in accordance with Article 88 to lay down the composition, appointment process, detailed tasks, audit procedures, including sanctions, referred to in paragraph 2, working methods and rules of procedure of the Forum.
2016/09/15
Committee: ENVI
Amendment 202 #
Proposal for a regulation
Article 11 – paragraph 4 a (new)
4a. When applying for EU type- approval, the manufacturers shall demonstrate that the design of vehicles, systems components and separate technical units does not incorporate strategies that unnecessarily reduce the performance exhibited during relevant test procedures when the vehicles, systems, components and separate technical units are operated under conditions that may reasonably be expected to be encountered in normal operation and use.
2016/09/15
Committee: ENVI
Amendment 206 #
Proposal for a regulation
Article 13 – paragraph 1 – point b
(b) following a reasoned request from an approval authority, provide that authority with all the information and documentation necessary to demonstrate the conformity of production of a vehicle, system, component or separate technical unit, this shall include any technical specifications at type approval and access to software and algorithms as requested;
2016/09/15
Committee: ENVI
Amendment 220 #
Proposal for a regulation
Article 20 – paragraph 4
4. The EU type-approval for the final stage of completion shall be granted only after the approval authority has verified that the type of vehicle approved at the final stage meets at the time of the approval all applicable technical requirements. Verification shall include a documentary check of all requirements covered by an EU type-approval for an incomplete type of vehicle granted in the course of a multi-stage procedure, even where granted for a different category of vehicle. It shall also include verification that performance of the systems that were granted type approval separately is still in conformity with those type approvals when incorporated into a whole vehicle.
2016/09/15
Committee: ENVI
Amendment 224 #
Proposal for a regulation
Article 22 – paragraph 1 – point b a (new)
(ba) detailed technical descriptions and calibration specifications for all emission- related components (Base Emission Strategy)
2016/09/15
Committee: ENVI
Amendment 225 #
Proposal for a regulation
Article 22 – paragraph 1 – point b b (new)
(bb) a list of all defeat devices or any Auxiliary Emission Strategy, including a description of the parameters that are modified by any AES and the boundary conditions under which the AES operate, and indication of which AES and BES are likely to be active under all range of ambient conditions, detailed technical descriptions and calibration specifications, as well as a detailed justification of each defeat device that results in a reduction in effectiveness of the emission control system, and rationale for why it is not a defeat device prohibited under Article 5(2) of Regulation 715/2007,
2016/09/15
Committee: ENVI
Amendment 226 #
Proposal for a regulation
Article 22 – paragraph 2
2. The information folder shall be supplied in an electronic format to be provided by the Commission bu. It may also be additionally supplied on paper.
2016/09/15
Committee: ENVI
Amendment 230 #
Proposal for a regulation
Article 23 – paragraph 4 – subparagraph 1
The approval authority and technical services shall have access to the software and algorithms of the vehicleafety and emissions-related software and hardware and to algorithms of the vehicle as well as an appropriate insight into the system development process of software and hardware, while taking into account their respective duties.
2016/09/15
Committee: ENVI
Amendment 231 #
Proposal for a regulation
Article 23 – paragraph 4 – subparagraph 1 a (new)
The manufacturer shall communicate to the approval authority and the technical service - in a standardised form - the version of the safety and emissions-related software at the time of the application for type-approval. In order to detect subsequent unlawful changes to the software, the technical service shall be entitled to mark the software by setting corresponding parameters.
2016/09/15
Committee: ENVI
Amendment 232 #
Proposal for a regulation
Article 23 – paragraph 4 – subparagraph 2
The approval authority and the responsible technical service may, by reasoned request, also require the manufacturer to supply any additional information neededwhich is necessary to take a decision on which tests are required, or to facilitate the execution of those tests.
2016/09/15
Committee: ENVI
Amendment 233 #
Proposal for a regulation
Article 23 – paragraph 4 – subparagraph 2 a (new)
The approval authority and the responsible technical service shall observe confidentiality where necessary in order to protect commercial secrets, unless it is in the public interest, subject to the obligation of information laid down in Article 9(3) in order to protect the interests of users in the Union.
2016/09/15
Committee: ENVI
Amendment 235 #
Proposal for a regulation
Article 24 – paragraph 2 – point c a (new)
(ca) the validity of the justification given for the installation of a defeat device in accordance with Art 5(2) of Regulation 715/2007
2016/09/15
Committee: ENVI
Amendment 237 #
Proposal for a regulation
Article 24 – paragraph 5 a (new)
5a. The approval authority may refuse to approve a vehicle emissions control defeat device on the basis of the information included in the information folder by consideration of currently best available technology. The approval authority shall refuse to grant EU type-approval where it finds that a defeat devices has been unlawfully incorporated.
2016/09/15
Committee: ENVI
Amendment 238 #
Proposal for a regulation
Article 24 – paragraph 6 a (new)
6a. The Commission shall adopt delegated acts in accordance with Article 88 to set out criteria according to which an application for one of the exceptions to the prohibition of vehicle emissions control defeat devices in accordance with Article 5(2) of Regulation (EC) No 715/2007 is evaluated and conditions under which it may be approved or rejected.
2016/09/15
Committee: ENVI
Amendment 241 #
Proposal for a regulation
Article 28 – paragraph 1
1. Compliance with the technical requirements of this Regulation and of the regulatory acts listed in Annex IV shall be demonstrated by means of appropriate tests in accordance with the relevant regulatory acts listed in Annex IV, performed solely and in full by designated technical services.
2016/09/15
Committee: ENVI
Amendment 242 #
Proposal for a regulation
Article 28 – paragraph 2
2. The manufacturer shall provide the approval authoritytechnical service with the vehicles, systems, components or separate technical units that are required under the relevant acts listed in Annex IV for the performance of the required tests.
2016/09/15
Committee: ENVI
Amendment 243 #
Proposal for a regulation
Article 28 – paragraph 3
3. The required tests shall be performed on those vehicles, systems, components and separate technical units that are strictly representative of the type to be approved.
2016/09/15
Committee: ENVI
Amendment 244 #
Proposal for a regulation
Article 28 – paragraph 3 – subparagraph 1 a (new)
In the case of whole vehicle type- approval, the authorities shall ensure that the vehicles selected for testing will not lead to the results that are systematically divergent from the performance when those vehicles are operated under conditions that may reasonably be expected to be encountered in normal operation and use.
2016/09/15
Committee: ENVI
Amendment 246 #
Proposal for a regulation
Article 29 – paragraph 2
2. An approval authority that has granted a whole-vehicle type-approval shall verify a statistically relevant number of samples of vehicles and certificates of conformity on their compliance with Articles 34 and 35 and shall verify that the data in the certificates of conformity are correct. An approval authority shall inspect every year at least 20% of all new car models which have been type- approved and produced.
2016/09/15
Committee: ENVI
Amendment 247 #
Proposal for a regulation
Article 29 – paragraph 4
4. In order to verify that a vehicle, system, component or separate technical unit conforms to the approved type, the approval authority that has granted the EU type-approval shall carry out checks or tests required for EU type-approval, applying best available testing technology, on samples taken at random at the premises of the manufacturer, including production facilities or dealership. These tests shall be carried out by a different technical service than the one that performed the original testing for the purpose of type-approval.
2016/09/15
Committee: ENVI
Amendment 251 #
Proposal for a regulation
Article 29 – paragraph 5
5. An approval authority that has granted an EU type-approval and establishes that the manufacturer no longer produces the vehicles, systems, components or separate technical units in conformity with the approved type, or establishes that the certificates of conformity no longer comply with Articles 34 and 35, even though production is continued, shall take the necessary measures to ensure that the procedure for conformity of production is followed correctly and immediately brought back into compliance or withdraw the type- approval.
2016/09/15
Committee: ENVI
Amendment 252 #
Proposal for a regulation
Article 30 – paragraph -1 (new)
-1. Member States shall ensure that there is no conflict of interest or commercial relationship between national authorities responsible for type approval and market surveillance activities, technical services and manufacturers as regards funding for the testing activities concerned.
2016/09/15
Committee: ENVI
Amendment 255 #
Proposal for a regulation
Article 30 – paragraph 1
1. Member States shall establish a national fee structure to cover the costs for their type-approvals and market surveillance activities as well as for activities, the type- approval testing and conformity of production testing and inspections carried out by the technical services they have designated.
2016/09/15
Committee: ENVI
Amendment 262 #
Proposal for a regulation
Article 30 a (new)
Article 30 a Funding of market surveillance activities 1. Member States shall impose an administrative charge on manufacturers to cover the costs of national surveillance activities required by this Regulation. This charge shall be proportionate to the services required from national type approval and surveillance authorities and testing services to perform their tasks and duties in line with the provisions of this Regulation. For the purposes of the above paragraph, Member States shall levy manufacturers a charge of EUR 10 per each vehicle sold on their territory in a given year. The charge shall be collected at national level and used to cover the costs, in the following year, of market surveillance activities required pursuant to the provisions of this Regulation. 2. Member States shall notify annually the details of the fees collected and the annual total cost of surveillance testing performed as a result to the other Member States and the Commission via the Forum established in article 10. The first notification shall be effected on 1 January 2019 [date of entry into force of this Regulation + 1 year]. 3. The Commission may adopt implementing acts in order to update the annual amount referred to in paragraph 1. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 87(2).
2016/09/15
Committee: ENVI
Amendment 263 #
Proposal for a regulation
Article 32 – paragraph 1 – subparagraph 1
The amendment shall be designated a ‘revision’ where the approval authority finds that despite the change in the particulars recorded in the information package the concerned type of vehicle, system, component or separate technical unit continues to comply with the applicable requirements for this type and that, therefore, no inspections or tests need to be repeated. When evaluating such revisions, the approval authority shall take into account the results of relevant market surveillance activities pursuant to Article 8 of this Regulation.
2016/09/15
Committee: ENVI
Amendment 264 #
Proposal for a regulation
Article 32 – paragraph 2 – subparagraph 1 – point b a (new)
(ba) the results of verification testing by either the Commission or the market surveillance authorities show non- conformity with any of the Union safety or environmental legislation;
2016/09/15
Committee: ENVI
Amendment 272 #
Proposal for a regulation
Article 37 – paragraph 3
3. The granting of EU type-approvals exempting new technologies or new concepts shall be subject to authorisation by the Commission. That authorisation shall be given by means of an implementing act. That implementing delegated act. That delegated act shall be adopted in accordance with the examination procedure referred to in Article 87(2)8.
2016/09/15
Committee: ENVI
Amendment 277 #
Proposal for a regulation
Article 49 – paragraph 2 – subparagraph 2
Where, in the course of that evaluation, the approval authority that granted the approval finds that the vehicle, system, component or separate technical unit does not comply with the requirements laid down in this Regulation, it shall require without delay the relevant economic operator to take all appropriate corrective measures to bring the vehicle, system, component or separate technical unit into compliance with those requirements, or take restrictive measures, either to immediately withdraw the vehicle, system, component or separate technical unit from the market, or to recall it within a reasonable period6 months, depending on the nature of the risk.
2016/09/15
Committee: ENVI
Amendment 279 #
Proposal for a regulation
Article 52 – paragraph 1 – subparagraph 2
The Member State mayshall refuse to register such vehicles until the economic operator has taken all appropriate corrective measures.
2016/09/15
Committee: ENVI
Amendment 281 #
Proposal for a regulation
Article 53 – paragraph 1
1. Where vehicles, systems, components or separate technical units accompanied by a certificate of conformity or bearing an approval mark do not conform to the approved type, or are not in conformity with this regulation or were approved on the basis of incorrect data, the approval authorities, market surveillance authorities or the Commission mayshall take the necessary restrictive measures in accordance with Article 21 of Regulation (EC) No 765/2008, to prohibit or restrict the making available on the market, registration or entry into service on the market of non-compliant vehicles, systems, components or separate technical units, or to withdraw them from that market or to recall them, including the withdrawal of the type-approval by the approval authority that granted the EU type-approval, until the relevant economic operator has taken all appropriate corrective measures to ensure that vehicles, systems, components or separate technical units are brought into conformity.
2016/09/15
Committee: ENVI
Amendment 286 #
Proposal for a regulation
Article 54 – paragraph 1
1. Where an approval authority or market surveillance authority finds that vehicles, systems, components or separate technical units are not in conformity with this Regulation or that the type-approval has been granted on the basis of incorrect data or that vehicles, systems, components or separate technical units accompanied by a certificate of conformity or bearing an approval mark do not conform to the approved type, it mayshall take all appropriate restrictive measures in accordance with Article 53(1).
2016/09/15
Committee: ENVI
Amendment 289 #
Proposal for a regulation
Article 57 – paragraph 3 – subparagraph 2
The approval authority shall carry out an evaluation to verify whether the proposed remedies are sufficient and timely enough, and it shall communicate the remedies that it has approved to the approval authorities of the other Member States and to the Commission without delay and make publically available a full report of the evaluation findings and proposed remedies.
2016/09/15
Committee: ENVI
Amendment 299 #
Proposal for a regulation
Article 71 – paragraph 8 – subparagraph 1
The type-approval authority shall be peer- reviewed by two type-approval authorities of other Member States every two yearsaudited by the Forum every two years in accordance with provisions of Article 10.
2016/09/15
Committee: ENVI
Amendment 303 #
Proposal for a regulation
Article 71 – paragraph 8 – subparagraph 2
The Member StatesForum shall draw up the annual plan for the peer-reviewaudit, ensuring an appropriate rotation in respect of reviewing and reviewed type-approval authorities, and submit it to the Commission.
2016/09/15
Committee: ENVI
Amendment 305 #
Proposal for a regulation
Article 71 – paragraph 8 – subparagraph 3
The peer-review shall includeaudit shall include a verification of the type approval procedures and correct implementation of the requirements of this Regulation, a random sample check of the type approvals issued and an on-site visit to a technical service under the responsibility of the reviewed authority. The Commission may participate in the review and decide on its participation on the basis of a risk assessment analysis.
2016/09/15
Committee: ENVI
Amendment 307 #
Proposal for a regulation
Article 71 – paragraph 8 – subparagraph 3 a (new)
If the audit demonstrates that the authority has breached any requirements of this Regulation or the vehicles, systems, components and separate technical units are not in conformity with the type approvals it issued, the authority shall immediately take all steps necessary to bring its procedures in compliance. The Member States may decide not to recognise the type approvals issued to vehicles, systems, components and separate technical units by the authority concerned on their territory until full compliance with the requirements of this Regulation is achieved.
2016/09/15
Committee: ENVI
Amendment 310 #
Proposal for a regulation
Article 71 – paragraph 9
9. The outcome of the peer-reviewaudit shall be communicated to all Member States and, to the Commission and third parties upon request, a summary report of the outcome shall be made publicly available. ItThe Forum shall be discussed by the Forum established in Article 10 and evaluate the results onf the basis of an assessment of this outcome carried out by the Commissaudits and shall ensure that the recommendations and issue recommendationsre implemented.
2016/09/15
Committee: ENVI
Amendment 311 #
Proposal for a regulation
Article 71 – paragraph 10
10. The Member States shall provide information to the Commission and the other Member States on how it has addressed the recommendations in the peer-reviewaudit report.
2016/09/15
Committee: ENVI
Amendment 316 #
Proposal for a regulation
Article 72 – paragraph 2
2. A Member State may designate an approval authority as a technical service for one or more of the categories of activities referred to in paragraph 1. Where an approval authority is designated as a technical service and is financed by a Member State, or is subject to managerial and financial control by that Member State, Articles 72 to 85 and Appendices 1 and 2 to Annex V shall apply.deleted
2016/09/15
Committee: ENVI
Amendment 317 #
Proposal for a regulation
Article 72 – paragraph 3
3. A technical service shall be established under the national law of a Member State and have legal personality, except for an accredited in-house technical service of a manufacturer, as referred to in Article 76.
2016/09/15
Committee: ENVI
Amendment 320 #
Proposal for a regulation
Article 73 – paragraph 2 – subparagraph 1
A technical service shall be an independent third-party organiszation or body that is notthat has no legal ties to any manufacturer or parts supplier, nor has itself any involvedment in the process of design, manufacturing, supply or maintenance of the vehicle, system, component or separate technical unit it assesses, tests or inspects.
2016/09/15
Committee: ENVI
Amendment 322 #
Proposal for a regulation
Article 73 – paragraph 2 – subparagraph 2
An organisation or body belonging to a business association or professional federation representing undertakings that are involved in the design, manufacturing, supply or maintenance of the vehicles, systems, components or separate technical units that it assesses, tests or inspects, may be considered as fulfilling the requirements of the first subparagraph, provided that its independence and the absence of any conflict of interest are demonstrated to the designating approval authority of the relevant Member State.deleted
2016/09/15
Committee: ENVI
Amendment 326 #
Proposal for a regulation
Article 76 – paragraph 1
1. An in-house technical service of a manufacturer may be designated for category AB activities as referred to in Article 72(1)(a) only with regard to the regulatory acts listed in Annex XV. An in- house technical service shall constitute a separate and distinct part of the manufacturer's company and shall not be involved in the design, manufacturing, supply or maintenance of the vehicles, systems, components or separate technical units that it assesses.
2016/09/15
Committee: ENVI
Amendment 328 #
Proposal for a regulation
Article 76 – paragraph 2 – point c a (new)
(ca) the in-house technical service shall be audited according to the provisions of Article 77;
2016/09/15
Committee: ENVI
Amendment 332 #
Proposal for a regulation
Article 76 – paragraph 3
3. An in-house technical service does not need toshall be notified to the Commission for the purposes of Article 78, but information concerning its accreditation shall be given by the manufacturer of which it forms part or by the national accreditation body to the type-approval authority at the request of that authorityas set out in Article 78.
2016/09/15
Committee: ENVI
Amendment 334 #
Proposal for a regulation
Article 77 – paragraph 1 – subparagraph 1
Before designating a technical service, the type-approval authority shall assess it in accordance with an harmonized assessment check-list that covers at least the requirements listed in Appendix 2 of Annex V. The assessment shall include an on-site assessment of the premises of the applying technical service, and, where relevant, of any subsidiary or sub- contractor, located inside or outside the Union.
2016/09/15
Committee: ENVI
Amendment 335 #
Proposal for a regulation
Article 77 – paragraph 1 – subparagraph 2
Representatives of the type-approval authorities of at least two other Member States shall, in coordination with the type- approval authority of the Member State in which the applicant technical service is established, and together with a representative of the Commission, form a joint assessment team and participate in the assessment of the applicant technical service, including the on-site assessment and witnessing the actual type-approval tests. The designating type-approval authority of the Member State where the applicant technical service is established shall give those representatives timely access to the documents necessary to assess the applicant technical service.
2016/09/15
Committee: ENVI
Amendment 336 #
Proposal for a regulation
Article 77 – paragraph 12
12. The approval authority that intends to be designated as a technical service in accordance with Article 72(2) shall document compliance with the requirements of this Regulation through an assessment conducted by independent auditors. Those auditors shall not belong to the same approval authority and shall comply with the requirements laid down in Appendix 2 of Annex V.deleted
2016/09/15
Committee: ENVI
Amendment 338 #
Proposal for a regulation
Article 89 – paragraph 1
1. Member States shall lay down the rules on penalties for infringement by economic operators and technical services of their obligations laid down in the Articles of this Regulation, in particular Articles 11 to 19 and 72 to 76, 84 and 85 and shall take all measures necessary to ensure that they are implemented. The penalties provided for shall be effective, proportionate and dissuasive. In particular the penalties shall be proportionate to the number of non-compliant vehicles registered in the concerned Member State market, or the number of non-compliant systems, components or separate technical unit made available on the concerned Member State market.
2016/09/15
Committee: ENVI
Amendment 339 #
Proposal for a regulation
Article 89 – paragraph 2 – point b
(b) falsifying test results for type- approval; or surveillance testing
2016/09/15
Committee: ENVI
Amendment 340 #
Proposal for a regulation
Article 89 – paragraph 2 – point c a (new)
(ca) use of illegal defeat devices
2016/09/15
Committee: ENVI
Amendment 343 #
Proposal for a regulation
Article 90 a (new)
Article 90 a Online Portal 1. The Commission shall establish an online portal for exchange of information on EU type-approvals between type- approval authorities, market surveillance authorities, Commission and third parties. 2. Commission, via the Forum referred to in Article 9, shall oversee the portal, in particular the maintenance of the type-approvals database, including regular updates, coordination of input information with relevant authorities and data security and confidentiality. 3. In the case of type-approvals, the database shall include the information required in Annexes I and III of this Regulation. Third parties shall have unlimited access to at least information contained in Certificates of conformity in line with Annex IX of this Regulation, as well as all at least the following information for independent third-party testing: (a) Test vehicle mass/weight (b) Test vehicle rolling resistance (c) Test temperature (d) Aerodynamic drags (e) Road load coefficients (f) CO2 emissions in gCO2/km at type approval (g) Auxiliary equipment used during testing (air conditioning, audio & media, other accessories) (h) Tyre details (model, manufacture, size & pressure) (i) Vehicle specific gear shift points (j) Driver mode in which the vehicle was 4. National authorities responsible for type-approval and market surveillance shall without delay update the database every time a new type-approval is issued or withdrawn, and every time non- conformity with this Regulation is found or any remedy action taken. 5. National authorities and Commission shall draw on existing portals, such as the EU Rapid Warning System (RAPEX) and the Information and Communication System on Market Surveillance (ICSMS) to ensure coordination, consistency and accuracy of the information provided to consumers and third parties. 6. The portal shall include a tool for consumers and other third parties to report independent third-party test results, faulty reports and any complaints about the performance of vehicles, systems, components, and separate technical units, including safety, environmental and fuel consumption performance. This tool shall be taken into account when choosing vehicles to be tested for the purposes of Article 8. 7. The portal shall be operational no later than 31 December 2019.
2016/09/15
Committee: ENVI
Amendment 346 #
Proposal for a regulation
Article 91 – paragraph 1 – point 3 a (new)
Regulation (EC) 715/2007
Article 5 – paragraph 2 – subparagraphs 1a and 1db(new)
(3a) in Article 5, the following subparagraphs are added to paragraph 2: 'Manufacturers seeking EU type-approval for a vehicle using a BES, AES or defeat device, as defined in this Regulation or Regulation 2016/646/EU, shall provide the type-approval authority with all information, including technical justification, that may be reasonably required by the type-approval authority to determine whether the BES or AES is a defeat device and whether a derogation to the prohibition on the use of defeat devices under Article 5(2) of Regulation (EC) 715/2007 is applicable. The approval authority shall not grant EU type-approval until it has completed its assessment and has determined that the type of vehicle is not equipped with a prohibited defeat device in accordance with this Article and Regulation (EC) No 692/2008.'.
2016/09/15
Committee: ENVI
Amendment 352 #
Proposal for a regulation
Article 96 – paragraph 1
1. This Regulation shall not invalidate any whole-vehicle type-approval or EU type-approval granted to vehicles or to systems, components or separate technical units before [PO: please insert the date of application as mentioned in Article 98]1 January 2018.
2016/09/15
Committee: ENVI
Amendment 353 #
Proposal for a regulation
Article 96 – paragraph 3
3. The validity of whole-vehicle type- approvals referred to in paragraph 1 shall terminate at the latest on [PO: please insert the date, which should be the date of application as mentioned in Article 98 + 5 years]1 January 2023 and approval authorities may only renew those whole-vehicle type-approvals in accordance with the provisions of Article 33 of this Regulation.
2016/09/15
Committee: ENVI
Amendment 354 #
Proposal for a regulation
Article 97 – paragraph 1
1. By 31 December 20xx [PO: please insert the year, which should be the year of application as mentioned in Article 98 + 5 years]23, Member States shall inform the Commission of the application of the type- approval and market surveillance procedures laid down in this Regulation.
2016/09/15
Committee: ENVI
Amendment 355 #
2016/09/15
Committee: ENVI
Amendment 431 #
Proposal for a regulation
Article 72 – paragraph 2
2. A Member State may designate an approval authority as a technical service for one or more of the categories of activities referred to in paragraph 1. Where an approval authority is designated as a technical service and is financed by a Member State, or is subject to managerial and financial control by that Member State, Articles 72 to 85 and Appendices 1 and 2 to Annex V shall apply.deleted
2016/09/20
Committee: TRAN
Amendment 432 #
Proposal for a regulation
Article 72 – paragraph 3
3. A technical service shall be established under the national law of a Member State and have legal personality, except for an accredited in-house technical service of a manufacturer, as referred to in Article 76.
2016/09/20
Committee: TRAN
Amendment 434 #
Proposal for a regulation
Article 73 – paragraph 2 – subparagraph 1
A technical service shall be an independent third-party organiszation or body that is notthat has no legal ties to any manufacturer or parts supplier, nor has itself any involvedment in the process of design, manufacturing, supply or maintenance of the vehicle, system, component or separate technical unit it assesses, tests or inspects.
2016/09/20
Committee: TRAN